Note: Other configuration changes can be
saved without <save/reboot> following
each individual change. However, after the
WAN settings are changed, the unit must
be rebooted. The interface can then be
accessed on the new IP address. If the
subnet of the encoder WAN setting has
changed, verify that the computer’s static
IP is changed to match the subnet of the
new IP address. If the IP address is
changed, the decoder <Connection
Setting> TCP/IP Connect IP must reflect
the new encoder IP address.
6. Select: <Video Settings> to change the
baud rate for PTZ control; bit rate, frame
rate and/or resolution for throughput
control.
Select: desired configuration changes
Select: <Apply>
Select: <Save/Reboot>
7. Only if desired, Select:<User Account> to
change default User ID and/or password
Select: <Apply>; insert new ID and/or
password at web browser prompt
Select: <Save/Reboot>
Note: If a change is made to the encoder GUI
User ID and/or password the same
changes must be recorded in the decoder’s
<Connection Setting> TCP/IP Connect
User ID and Password.
LED
Status Description
PWR
ON
Power supplied to the unit
(allow 30 secs to settle)
OFF No power to the unit
RX
FLASH
Camera sending
communication to encoder
OFF Normal conditions
TX
ON PTZ control signals being
sent from decoder
OFF Normal conditions
Ethernet RJ45 Port Status LED
Each RJ45 Ethernet port has 2 indicators, a yellow
lamp & a green lamp. The yellow lamp indicates video
is streaming, the green lamp indicates port link state.
Link Status
(Green)
ON Link connected
OFF
No connection
LINK/ACT
(Yellow)
FLASH
Streaming video
Note: A solid RX LED indicates a data wiring or
other data related error.
Dip Switch Default Configuration
RS485/422 RS232
1 to 4 - ON 1 to 4 - OFF
5 to 8 - OFF 5 to 8 - ON
PTZ Data Wiring Configuration
RS-485, 2 wire: Camera RX to encoder TX+
Camera RX- to encoder TX-
RS-422, 4 wire: Camera TX+/- to encoder TX+/-
Camera RX+/- to encoder RX+/-
RS-232: transmit to encoder TX+
receive to encoder RX+
ground to encoder GND
Contact Closure Default Configuration
ENC-A-W* Encoder Action DEC-A-W* Decoder
D01
DO2
DI1 DI2 D01 D02 DI1 DI2
ON ON ON ON Normal state OFF OFF ON ON
OFF
ON ON ON Short decoder DI1
to gnd
GND
ON OFF ON ON Short decoder DI2
to gnd
GND
GND Short encoder DI1
to gnd
ON OFF ON ON
GND Short encoder DI2
to gnd
OFF ON ON ON
Note: Triggers from default configurations shown. See
decoder interface settings to configure other trigger
options.
Need Help/Troubleshooting?
Visit our website http://www.kbcnetworks.com or
contact your nearest KBC office or dealer:
APAC:
Phone: +65 98463323
Email: apactechsupport@kbcnetworks.com
EMEA:
Phone: +44(0)1622 618787
Email: emeatechsupport@kbcnetworks.com
USA:
Phone: +1 949-297-4930
Toll Free: +1 888-366-4276
Email: techsupport@kbcnetworks.com
ENC-A-W*
Encoder
QSG_Encoder_MPEG4-Rev1206 www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2012
(29 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales