Kbc-networks WES2HT 9dBi Multipoint Host Manual de usuario
Busca en linea o descarga Manual de usuario para Accesorios De Computador Kbc-networks WES2HT 9dBi Multipoint Host. KBC Networks WES2HT 9dBi Multipoint Host User Manual Manual de usuario
- Pagina / 2
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Introduction
Welcome to KBC Networks’ Quick Start
Guide for the WES2HT point-to-
multipoint host with 9dBi antennas.
This document provides some tips to get up and
running. More detailed information can be found on
our website (please see Downloads).
Features:
• 5GHz operation
• MIMO technology
• Dynamic Frequency Selection &
Transmission Power Control
• Antenna alignment & signal survey tools
• IP66 casing
• Gigabit Ethernet
System Contents
Qty
Description
1 WES2HT Single point host module with PIM and
power supply
1 Cable weather-proof kit assembly
1 Wall or pole-mount bracket and assembly kit
including:
1 Bracket body
1 Pole clamp bracket
1 Connecting piece 1
1 Connecting piece 2
1 50mm, 1.98” long ¼” hex bolt
2 ¼” hex nuts
1 27mm, 1.06” long ¼” hex bolt
2 Flat washers 15mm, 0.59”
2 Locking washers 10mm, 0.39” long
1 U bolt
2 ¼-20 lock washers
Downloads
Installation manual: for other features & functions:
http://www.kbcnetworks.com/downloads
Specification Sheets:
http://www.kbcnetworks.com/downloads
Equipment Required for Physical Deployment
Two straight-through Ethernet cables are required
for connection from the WES2HT to PoE enabled
switches or PIMs.
Note:
WES2HT requires a CAT6 or Gigabit Ethernet
cable. KBC recommends shielded outdoor rated Ethernet
cables when connecting near power outlets & when
exposed to the elements.
Physical Deployment
This equipment must be installed and operated in
accordance with instructions found in the KBC
Networks manual. The orientation of the units must
be as depicted, failure to comply with these
instructions will invalidate warranty.
Configuring the WES2HT
-
MP
Host
Note:
The WES2HT comes pre-configured from the
factory and does not require custom settings for basic
operation. Please refer to the documentation provided
for pre-set configuration settings.
If custom settings are required and/or desired,
please set the custom configurations as follows:
Configuring the Host unit:
1. Connect the PIM, PoE 802.3af or 802.3at
compliant sourcing device to the Ethernet
port of the WES2HT Host PoE unit.
2. Allow 60s for the unit to boot.
3. Verify that the static IP address on the
laptop is set to 192.168.1.x subnet.
4. Open a web browser to access the Host on
its 192.168.1.200 IP address; this is the
default address for the unit.
5. Enter the following to access the GUI:
ID: admin Password: admin
Note: Ensure that all other network interface
connections including your laptop Wifi are disabled.
6. Select: <Interference Analyzer> to
determine which frequencies are available
in your location.
Select: one of the available channels
Select: <Apply Settings>
Select: <Save>
Note: Point-to-point Host/APs and their respective
Clients must be MAC locked to each other.
Quick Start
Guide
WES2HT 9dBi
Multipoint Host
QSG-WES2HT_9dBi_MP_Host-Rev1311
www.kbcnetworks.com
Copyright © KBC Networks Ltd. 2013
1
2
Indice de contenidos
Pagina 1 - Quick Start
Introduction Welcome to KBC Networks’ Quick Start Guide for the WES2HT point-to-multipoint host with 9dBi antennas. This document provides some
Pagina 2
Topology/Mapping Option If you have chosen the mapping option on your unit you will be able to view system configuration and health all on one pa
Relacionado con productos y manuales para Accesorios De Computador Kbc-networks WES2HT 9dBi Multipoint Host
(5 paginas)TOA Electronics WM-5270UHF manuali
Manuali dei proprietari e guide per l'utente per Microfoni TOA Electronics WM-5270UHF.
We fornisce 2 manuali pdf TOA Electronics WM-5270UHF per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Comentarios a estos manuales